Key blank for Zadi keys - check key profile before ordering

Key blank with plastic head for models without immobiliser chips

 This part is due back in stock soon, call 01484 841395 to reserve yours

Alternator upgrade kit for Bosch systems containing stator windings, wound rotor and replacement diode board. The superior design alternator has an output up to 300% greater than the original Bosch system. You may wish to fit a plastic alternator spacer ENA18150 if your model does not have one of these already (to improve cooling of the alternator). You will need front crank seal ENA90428 (Bosch seal) if you wish to fit this to a bike with a Saprisa charging system. This kit reuses your existing Bosch regulator and stator plate with brush holder, see ELA29703 for a replacement regulator and ELA17452 for brush holders.

• Outputs 600W @5000 RPM
• Supplied with rotor removal tool
• For tapered crankshafts

1. Remove stator and rotor using the supplied rotor removal tool
2. Remove the old stator windings from the stator plate
3. Solder in the new stator widing wires to the connection block on the stator plate and reconnect the
4. Mount the replacement diode board, this should be protected from the weather but cooled by passing air
5. Connect up the system as follows: Terminals U,V and W take the three yellow wires which should be connected to the stator plate block; Y goes to Y on the stator plate; The brown wires go to earth (we recommend using some earth sleeve on these if possible); Red goes to the battery positive terminal; regulator wiring remains as before (D+ to diode board, D- to earth and DF to brush holder)
6. Check charge warning light is working (earth DF wire at stator to check bulb function)
7. Turn motor over by hand to ensure everything is seated correctly, there should be an air gap between the stator windings amd rotor
Fit alternator cover and spacer

 This part is available by special order, request a quote

Oil temperature sensor, brass threaded body

 This part is available by special order, request a quote

 887421 MG887421

Also fits Aprilia 900 Dorsoduro, Aprilia 900 Shiver

Replacement starter motor for 2006 on models. Also known as 97729R

This is a less expensive aftermarket replacement for the OE starter.
Not interchangeable with Valeo and Bosch starters from earlier models. Get a £20 discount on this part if you send us your faulty but reconditionable starter motor

 This part is due back in stock soon, call 01484 841395 to reserve yours

 05730730 GU05730730 05 73 07 30
 0573 0730 0573.0730 05.73.07.30

Switch used as rear stop switch or clutch switch

Used as rear stop light switch on V85TT

 This part is available by special order, request a quote

2D000325

Also fits Aprilia RSV 1000, Aprilia Tuono

Factory heated grip kit to keep your hands toastie warm all year round.

Features 3 temperature settings

 This part is available by special order, request a quote

2S002029

Replica fuse box cover with clear lid and securing screw.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 17743000 GU17743000 17 74 30 00
 1774 3000 1774.3000 17.74.30.00

HT ignition lead. Copper core lead with integrated plug cap and threaded coil connector.

 This part is due back in stock soon, call 01484 841395 to reserve yours

2D000206

Complete electronic ignition kit containing distributor mounted ignition pickup, fittings and amplifier unit. Requires a pair of 12v coils ELA14500
Tacho will not work with this kit unless a amplifier is bought (enquire for details)
2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. See this link for fitting instructions.

 This part is available by special order, request a quote

Fuel injector

Genuine Marelli part

 Order now and we will post your order within 7 days.

 32115710 GU32115710 32 11 57 10
 3211 5710 3211.5710 32.11.57.10